1. Switch Room: The Eielson switch room was surveyed by General Dynamics on 1/17/01. The new GFE equipment is to be installed and cabled by General Dynamics as shown in the attached floor plan drawing (Attachment E). The room has a concrete slab floor and the cables will run on a combination of existing and new General Dynamics provided and installed cable rack. The Government must ensure that floor will withstand the weight of the new equipment. The new equipment will be anchored to the floor using seismic expansion shield type anchors.

1. Electrical requirements: General Dynamics is providing a new 4 position fuse panel and 150A fuses to be mounted in the PWR BD that will be used to power the new MCAM2 line-up. Only 2 of the 4 fuse positions will be used at this time.

1. MDF requirements: New Homaco wire-wrap type MDF blocks for the GFE equipment will be provided and installed by General Dynamics.
2. DSX requirements: General Dynamics is providing 1 new 64 jack, 23" front cross connect DSX panel that will be mounted in the DSX 00 rack.

.

The following is an Installation Support Requirements Document (ISRD) required for the EFI& T of GFE frame relocation at the Host digital phone switching system located at Eielson AFB Alaska. This ISRD details a set of support items or services that may be required of the Government during an upgrade/installation.

This ISRD covers the upgrade/installation. Deinstallation of the system from the original site was not considered. Deinstallation would potentially require the Government to be responsible for additional support tasks at the original site such as decommissioning, inventory, transportation, etc. (as applicable).

Post installation tasks such as input of service orders and system operation tasks are also not addressed in this document.

General Dynamics will design the system to meet the site specific SOW seismic zone requirements. The Government shall be responsible for all existing equipment unless stated in the SOW (as applicable).

The Government shall, if required, provide additional floor bracing to support the equipment and infrastructure loading. Refer to the General Dynamics Office Drawing for equipment weights, dimensions, and equipment layouts (as applicable).

The Government shall ensure the maximum deviation from the established floor elevation should not exceed 3/4". The maximum difference in elevation between high and low points in any given 20' square should not exceed 3/4" (as applicable).

The Government shall ensure the minimum Switch Room heights as follows: (as applicable.)

The Government shall ensure that a clearance from the finished floor and the underside of the lowest obstruction, such as vent ducts, beams, false ceilings, water sprinklers, etc., will be a minimum of 8'-0" for all areas associated with the Meridian SL-100 switch (as applicable).

General Dynamics will provide to the Government the quantity and size of breakers required; the Government shall:

9. AC Power Requirements :

Government shall run, secure, & terminate commercial AC from TPP to any and all General Dynamics or GFE provided rectifiers(To include all wiring and conduit.)

The Government shall provide a secure and dry storage/staging facility for all installation related materials adjacent to or as close by the switch area as is practical.

The Government shall provide transportation support for the equipment that is stored in a location other than the switch facility. A 24 hour notice will be given by the GTE Site Supervisor regarding the transfer of equipment. A truck with a lift gate, a forklift, and a dolly are recommended for delivering the materials to the installation site. The Government shall be responsible for delivering switch materials from the storage area to a pre-established point within the switching facility.

The Government shall ensure entry to the facility of all equipment.

The Government shall indicate the availability of loading docks and equipment elevators.

The Government shall ensure that there is a route between the unloading area and the Switch Room where no restrictions will be encountered with less clearance than 30" wide (side to side) and 84" high (floor to obstructions).

2.15 Environmental Air Cleanliness : See Site Survey Report (Attachment B).

The Government shall ensure that the required ambient temperature range of the switching area is between 10 and 30 degrees centigrade (50 to 86 degrees Fahrenheit), with extreme limits set at 5 to 49 degrees Centigrade (41 to 120 degrees Fahrenheit). The maximum rate of temperature cycling should not exceed one degree Centigrade per minute. Extreme temperature and relative humidity conditions are based on a maximum duration of up to 72 continuous hours and up to 15 days per year. The battery manufacturer recommends that the battery temperature be maintained at 77 degrees Fahrenheit for maximum battery life efficiency. The required operating relative humidity range is between 20 and 50 percent with extreme limits set at 20 to 80 percent.

The Government shall provide sufficient cooling for all site equipment.

2.8 Grounding : See Site Survey Report (Attachment B).

The Government shall be responsible for all aspects of the outside plant installation.

20. MDF : See Site Survey Report (Attachment B).
21. Cable Vault: See Site Survey Report (Attachment B).
22. Battery Room Requirements : See Site Survey Report (Attachment B)
23. Generator Requirements: See Site Survey Report (Attachment B)
24. Cable Ports : See Site Survey Report (Attachment B).

The Government shall provide all site utilities (water, sewage, etc.).

The Government shall ensure that adequate room lighting will be provided in all rooms associated with the Meridian SL-100 Switch. The lighting plan should be arranged in such a manner that the illumination is directed toward the switch aisles. Additional lighting should be provided at the front and rear of interface frames and the Main Distribution Frame (MDF) to facilitate detailed installation tasks. Aisle lighting will be 50' candles at 30" above the floor.

The Government shall provide and install any required fire detection and/or protection equipment that may be required according to the governing codes, including OSHA directives.

The Government shall provide a fire protection system.

The Government shall provide a site alarm system per the Government’s requirements, such as smoke, water, and intrusion. General Dynamics will, where possible, connect General Dynamics furnished equipment alarms to this system if required by the site SOW.

The Government shall be responsible for correcting all governing building/OSHA code violations (i.e., asbestos, lead paint, etc.).

The Government shall ensure that the allocated space for the Meridian SL-100 and all associated equipment are provided a positive ventilation.

The Government shall renovate the site facility as needed prior to installation per the General Dynamics Office drawings.

The Government shall furnish General Dynamics a site specification sheet (interior/exterior building styles). General Dynamics will furnish any materials and/or services required to restore any damages to the work location back to its original condition (including painting, replacing floor tiles, etc.) in accordance with Government specifications.

The Government shall make adequate parking space available for the installation team within a reasonable distance from the switch site.

The Government shall provide to site survey and installation personnel escorted or unescorted security clearances required for access during normal business hours to all areas associated with the installation. If required, General Dynamics will request access outside normal business hours.

The Government shall witness and authenticate all testing, QA/QC inspections, and audits.

The Government shall notify General Dynamics as soon as possible of any planned outages.